Our organization is counted among the leading and trusted manufacturers and exporters of a wide range of Power Supply devices. Designed in strict conformation with industry defined norms and standards, these instruments are offered in varied technical specifications so as to meet the application based requirements of the clients in different industry verticals. Highly reliable, functionally efficient, low in maintenance and durable, the range can be availed at industry leading prices.
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
| Variable Power Supply |
|
| High Voltage Power Supply |
|
| HMI INTERFACE FOR USING DESIRED VOLTAGE AND CURRENT | |
| Metering: | 3 digit DPM |
| HIGH PRECISION AND CONTROL THROUGH PROGRAMMING | |
| Meter Accuracy: | ±3 counts. |
| Constant Voltage Mode: |
|
| Constant Current Mode: Regulation |
|
| Overload Protection: | Automatic overloads and short circuit protection. |
| Transient Response: | Within one second of set output voltage for load change from 10% to 90% |
| Stability: | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature: | 0-50 degree |
| INPUT VOLTAGE | 230 V AC / 1 PHASE 50HZ |
| OUTPUT VOLTAGE AC | 24V AC, 48V AC, 110V AC |
| OUTPUT VOLTAGE DC | 24V DC, 48V DC, 110V DC |
| CAPACITY | 0-20AMPS |
| PROTECTION | CONSTANT CURRENT AND HRC FUSE (INSIDE) |
| OPERATION | CONSTANT CURRENT AND CONSTANT VOLTAGE |
| OPERATING TEMP | 25-45°C |
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
| Variable Power Supply |
|
| High Voltage Power Supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts. |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection. |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
- Digital Output Metering 3 Digit DPM
- Constant Voltage/Constant Current Operation
- High Stability and Close Regulation ±0.01%
- Proven Reliability and Endurance
- Remote Sensing Facility for Higher ratings
- Special voltage and current ratings available on request
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
|
Variable Power Supply |
|
| High Voltage Power Supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts. |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection. |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
- Different types of current and Amps rating can be used.
- real time process for all ports can be done simultaneously.
- Digital Output Metering 3 Digit DPM
- Constant Voltage/Constant Current Operation
- High Stability and Close Regulation ±0.01%
- Proven Reliability and Endurance
- Remote Sensing Facility for Higher ratings
- Special voltage and current ratings available on request
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts. |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection. |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
| INPUT VOLTAGE | 415 V AC / 3 PHASE 50HZ |
| OUTPUT VOLTAGE | 0-20 V DC |
| CAPACITY | 0-100 AMPS |
| PROTECTION | CONSTANT CURRENT AND HRC FUSE (INSIDE) |
| OPERATION | CONSTANT CURRENT AND CONSTANT VOLTAGE |
| OPERATING TEMP | 25-45°C |
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
| INPUT VOLTAGE | 415 V AC / 3 PHASE 50HZ |
| OUTPUT VOLTAGE | 0-20 V DC |
| CAPACITY | 0-300 AMPS |
| PROTECTION | CONSTANT CURRENT AND HRC FUSE (INSIDE) |
| OPERATION | CONSTANT CURRENT AND CONSTANT VOLTAGE |
| OPERATING TEMP | 25-45°C |
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts. |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection. |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
| INPUT VOLTAGE | 415 V AC / 3 PHASE 50HZ |
| OUTPUT VOLTAGE | 0-20 V DC |
| CAPACITY | 0-500 AMPS |
| PROTECTION | CONSTANT CURRENT AND HRC FUSE (INSIDE) |
| OPERATION | CONSTANT CURRENT AND CONSTANT VOLTAGE |
| OPERATING TEMP | 25-45°C |
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| Fixed Power supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts. |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection. |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
| INPUT VOLTAGE | 230 V AC / 50HZ |
| OUTPUT VOLTAGE | +15 V , -15 V |
| CAPACITY | 3 A |
| PROTECTION | FUSE |
| OUTER CASE | HIGH DURABLE MS |
- Digital Output Metering 3 Digit DPM
- Constant Voltage/Constant Current Operation
- High Stability and Close Regulation ±0.01%
- Proven Reliability and Endurance
- Remote Sensing Facility for Higher ratings
- Special voltage and current ratings available on request
K-PAS offers a range of Linear DC Regulated Power Supplies for use in Laboratories & Industries. Output voltage and current values are displayed on a 3 digit DPM. There are various models to choose from, with output power ranging from 30- 30000 Watts. Output voltage of 0-16V, 0-32V, 0-64V, 0-100V and 0-300V,0- 500V. DC is available for single output supplies.
There is Dual output models with two independent isolated outputs. These outputs could be connected in series or parallel to double the voltage or current. All the models operate in either constant voltage ornconstant current mode and are fully protected against continuous output short circuit and overload.
The Power Supply employs the time proven series pass regulator technique. The Power Supply is forced air cooled using the best type of heat sink available and is housed in an enclosure which is sturdy, attractive and easily accessible for servicing.
This model employs constant voltage/current limiting technique, wherein the current limit comes into operation, whenever the load current is approximately 10% above the rated current.
The output is fully protected against over load, short circuit and voltage reversal due to reactive loads. The output sourced is isolated from the chassis. The output is brought out through terminal block. The output can also be monitored by a digital meter which is provided on the front panel.
| High Voltage Power supply |
|
| Metering | 3 digit DPM |
| Meter Accuracy | ±3 counts. |
| Constant Voltage Mode |
|
| Constant Current Mode: Regulation |
|
| Overload Protection | Automatic overloads and short circuit protection. |
| Transient Response | Within one second of set output voltage for load change from 10% to 90% |
| Stability | Total drift within 8 hours, after warm up. Less than 0.5% in constant voltage/current mode with constant line, load and ambient temperature conditions. |
| Operating Temperature | 0-50 degree |
| INPUT VOLTAGE | 230 V AC / 1 PHASE 50HZ |
| OUTPUT VOLTAGE AC | 24V AC,48V AC, 110V AC |
| OUTPUT VOLTAGE DC | 24V DC, 48V DC, 110V DC |
| CAPACITY | 0-20AMPS |
| PROTECTION | CONSTANT CURRENT AND HRC FUSE (INSIDE) |
| OPERATION | CONSTANT CURRENT AND CONSTANT VOLTAGE |
| OPERATING TEMP | 25-45°C |
